View AT-128128H1FI-00H_4463369.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

AMP I RE
SPECIFICATIONS FOR LCD MODULE
CUSTOMER CUSTOMER PART NO. AMPIRE PART NO. APPROVED BY DATE
Approved For Specifications Approved For Specifications & Sample
AT-128128H1FI-00H
APPROVED BY
CHECKED BY
ORGANIZED BY
Date : 2003/2/21
AMPIRE CO., LTD.
1
RECORD OF REVISION
Revision Date 2002/8/26 2002/8/27 2002/8/29 2002/8/30 2002/9/23 2003/2/21 New Release Added the block of TAB solder dimension Modify the LCM outline dimension Added the TCP IC dimension Modify the LCM outline dimension Added the LCM default setting Modify the LCM passive component (Page 14) (Page 14) (Page 14) (Page 15) (Page 6) (Page 11) Contents
Date : 2003/2/21
AMPIRE CO., LTD.
2
1
FEATURES
(1) Display format : 128x128 dots, 1/128 duty. (2) Construction : LCD panel, TAB IC and FPC. (3) Display type : FSTN , Transflective, Positive , 6 o'clock view (4) Controller : HD66750S or equivalent (5) LCD polarizer : New P1 polarizer. (6) +2.8V single power input. (7) Built-in temp compensation circuit. (8) Extend temperature type.
2
MECHANICAL DATA
Parameter Dot size Dot pitch Viewing area Module size Stand Value 0.199(W) x 0.219(H) 0.213(W) x 0.233(H) 30.5(W) x32.0 (H) 36.3(W) x 82.8(H) x 1.4 max.(T) Unit mm mm mm mm
3
ABSOLUTE MAXIMUM RATINGS
Parameter Logic Circuit Supply Voltage LCD Driving Voltage Input Voltage Symbol VDD-VSS VLCD-VSS VI TOP TSTG Min -0.3 0 -0.3 -20 -30 Max +4.6 20.0 VDD+0.3 75 80 Unit V V V C C
Extend temp. type
Operating Temp. Storage Temp.
Date : 2003/2/21
AMPIRE CO., LTD.
3
4
ELECTRO-OPTICAL CHARACTERISTICS
Parameter Logic Circuit Supply Voltage LCD Driving Voltage (FSTN ) Input Voltage Symbol VDD-VSS VO-VSS Condition --20 C 25 C 70 C VIH VIL Logic Supply Current Contrast Rise Time Fall Time Viewing Angle Range IDD --VDD 3.3V Min 2.4 ---0.7VDD -0.3 -Typ 2.8 13.55 12.8 12.13 --0.2 Max 3.6 ---VDD 0.15 VDD 0.4 V V mA Unit V V Note
----- Electronic Characteristics -----
----- Optical Characteristics ( FSTN ) ----CR tr tf f b l r Frame Frequency fF 25C 25C 25C 25C 25C & CR2 --------7 200 200 40 30 35 35 64 --------Hz Deg. ms ms Note 3 Note 1 Note 2
(NOTE 1) Contrast ratio : CR = (Brightness in OFF state) / (Brightness in ON state)
Date : 2003/2/21
AMPIRE CO., LTD.
4
( NOTE 2 ) Response time :
(NOTE 3) Viewing angle
Date : 2003/2/21
AMPIRE CO., LTD.
5
5
BLOCK DIAGRAM
C17 DOT 1 C64 128X128 LCD PANEL C113 C128 S1
C1 C16
C65
C112 S 128
COM128/1 COM113/16 COM64/65 COM17/112 LCD MODULE SEG1/128 SEG128/1 C128 HD66750S (TOP VIEW)
COM112/17 COM65/64 COM16/113 COM1/128
PIN 15
PIN 1
Default Setting: Symbol
IM[2:0] OPOFF TEST DB[7:0] VTEST
H/L LHH L L L NC
Turn on amplifier Test pin 8-bit data bus Test Pin
Description
8080 System 8-bit bus interface
Date : 2003/2/21
AMPIRE CO., LTD.
6
6
INTERFACE
No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Symbol VDD D7 D6 D5 D4 D3 D2 D1 D0 /RES /CS A0 /WR /RD VSS
Function Power supply for logic circuit
8-bit data bus for 80 series MPU
Reset pin .Initializes the LSI when low Chip select at low Select register Lo:Index/status Data Write Data Read Ground (0V) Hi:Control
Date : 2003/2/21
AMPIRE CO., LTD.
7
7
Software setting
Please must follow the blow setting. Otherwise the temp consumption circuit can't work very well. These setting are related to temp consumption circuit, especially in Power control.
Power control
R/W 0 0 RS 1 1 DB15 DB14 DB13 DB12 DB11 DB10 DB9 DB8 DB7 * * * BS2 BS1 BS0 BT1 BT0 * 0 0 0 0 0 1 1 1 0 1/10 BIAS 7-TIMES DB6 DB5 DB4 DB3 DB2 DB1 * DC1 DC0 AP1 AP0 SLP 0 1 1 0 1 0 4-DIVIDED SMALL DB0 STB 0
Contrast control
R/W 0 0 RS 1 1 DB15 DB14 DB13 DB12 DB11 DB10 DB9 DB8 * * * * * * * * 0 0 0 0 0 0 0 0 DB7 DB6 DB5 * * CT5 0 0 1 DB4 DB3 DB2 DB1 DB0 CT4 CT3 CT2 CT1 CT0 0 1 0 0 0 28 (HEX) , 40 (DEC)
Date : 2003/2/21
AMPIRE CO., LTD.
8
8
TIMING CHARACTERISTICS
80-SYSTEM VDD=1.8to2.4V Item Symbol Min tCYCW Bus cycle time tCYCR PW LW Lo level pulse width PW LR PW HW Hi-level pulse width PW HR Enable rise/fall time Address set-up time (RS, R/W to E) Address hold time Write Data set-up time Write Data hold time Read Data delay time Read Data hold time tWRr,tWRf tAS tAH tDSW tH tDDR tDHR
Read Write
VDD=2.4to3.6V Min 380 500 Max --
Unit
Max --
600 800
Write120 Read
--
70 250
--
350
Write300 Read
--
150 150
-ns 25 ----200 --
300 -50 20 60 20 -5 25 ----300 --
-50 20 60 20 -5
Date : 2003/2/21
AMPIRE CO., LTD.
9
Date : 2003/2/21
AMPIRE CO., LTD.
10
9
BOM List
C5 R5 C4 C3
R1
C11 C7 C8 C9
C10
C12
C2 C1 C6 R4
Q1
R2
RTH
R3
Position R1 R2 R3 R5 RTH Q1 C1~C12
Value 330K ohm 1K ohm 6.8K ohm 0 ohm 10K ohm 2SC4617 1UF
Remark Resister Resister Resister Resister Thermistor Transistor Capacitor
OLB tape size : 33mm x 8 mm
Protection tape size : 35mm x 8 mm
Date : 2003/2/21
AMPIRE CO., LTD.
11
10 QUALITY AND RELIABILITY 10.1 TEST CONDITIONS
Tests should be conducted under the following conditions : Ambient temperature : 25 5C Humidity : 60 25% RH.
10.2
SAMPLING PLAN
Sampling method shall be in accordance with MIL-STD-105E , level II, normal single sampling plan .
10.3 ACCEPTABLE QUALITY LEVEL
A major defect is defined as one that could cause failure to or materially reduce the usability of the unit for its intended purpose. A minor defect is one that does not materially reduce the usability of the unit for its intended purpose or is an infringement from established standards and has no significant bearing on its effective use or operation.
10.4 APPEARANCE
An appearance test should be conducted by human sight at approximately 30 cm distance from the LCD module under flourescent light. The inspection area of LCD panel shall be within the range of following limits.
Date : 2003/2/21
AMPIRE CO., LTD.
12
10.5 INSPECTION QUALITY CRITERIA
Item Function Dimension Black spots Description of defects Class of Defects Major Major Minor Acceptable level (%) 0.65 1.5 2.5
Black lines
Bubbles in polarizer Color uniformity Glass Scratches Contrast ratio Response time Viewing angle
Short circuit or Pattern cut Deviation from drawings Ave . dia . D area A area B Disregard D0.2 3 4 0.2 0.5 for N = 1 Rainbow color or newton ring. Obvious visible damage. See note 1 See note 2 See note 3
Minor
2.5
Minor Minor Minor Minor Minor Minor
2.5 2.5 2.5 2.5 2.5 2.5
Zone A active area Zone B viewing area
Date : 2003/2/21
AMPIRE CO., LTD.
13
10.6 RELIABILITY
Test Conditions Test Item High Temperature Operation Low Temperature Operation High Temperature Storage Low Temperature Storage Thermal Shock Test Humidity Test Extend Temp. type 753C , t=96 hrs -203C , t=96 hrs 803C , t=96 hrs -303C , t=96 hrs -30C ~ 25C ~ 80C 30 m in. 5 min. 30 min. ( 1 cycle ) Total 5 cycle 40 C, Humidity 90%, 96 hrs 1,2 1,2 1,2 1,2 Note
Sweep frequency : 10 ~ 55 ~ 10 Hz/1min Amplitude : 0.75mm Vibration Test (Packing) 2 Test direction : X.Y.Z/3 axis Duration : 30min/each axis Note 1 : Condensation of water is not permitted on the module. Note 2 : The module should be inspected after 1 hour storage in normal conditions (15-35C , 45-65%RH). Definitions of life end point : Current drain should be smaller than the specific value. Function of the module should be maintained. Appearance and display quality should not have degraded noticeably. Contrast ratio should be greater than 50% of the initial value.
Date : 2003/2/21
AMPIRE CO., LTD.
14
11 HANDLING PRECAUTIONS
(1) A LCD module is a fragile item and should not be subjected to strong mechanical shocks. (2) Avoid applying pressure to the module surface. This will distort the glass and cause a change in color. (3) Under no circumstances should the position of the bezel tabs or their shape be modified. (4) Do not modify the display PCB in either shape or positioning of components. (5) Do not modify or move location of the zebra or heat seal connectors. (6) The device should only be soldered to during interfacing. Modification to other areas of the board should not be carried out. (7) In the event of LCD breakage and resultant leakage of fluid do not inhale, ingest or make contact with the skin. If contact is made rinse immediately. (8) When cleaning the module use a soft damp cloth with a mild solvent, such as Isopropyl or Ethyl alcohol. The use of water, ketone or aromatic is not permitted. (9) Prior to initial power up input signals should not be applied. (10) Protect the module against static electricity and observe appropriate anti-static precautions.
Date : 2003/2/21
AMPIRE CO., LTD.
15
12 OUTLINE DIMENSION
i
~ 3/4A I
Date : 2003/2/21
AMPIRE CO., LTD.
o
u
q
16

▲Up To Search▲

Price & Availability of AT-128128H1FI-00H

	To Download AT-128128H1FI-00H Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .